Can anyone clarify for me, which side of the engine the power steering pump goes on for a '72 232 six? I believe it's the left (passenger) side as the AC and ...
email me privately with your address... I can xerox the illustration page from the parts manual... and I also have the service manual to go by. The PS pump was...
Hello everyone, I'm looking for a Sun Tach model ST-602 for a '69 SC/Rambler. If anyone has one for sale please let me know. Thank You Pete Merrow Gorham,...
i am going to sell my 1970 amc gremlin is any one is interested in it go to www.gremlinx.com and look in the rides section on page #5 and my car is #46. if you...
Bill, I would have to agree that this seems excessive cost for such a part. Perhaps the high bidders, of which there were 3 who were willing to pay in excess...
Bill, On my 76, 232 it goes like this.... When you look at the front of the engine the power steering pump is on the drivers side. It is run by the rear belt...
Hello, Would anyone be interested in a "73 Hornet Sportabout with a little over 31,000 original miles on it? It's original. Any ??? just let me know and email...
I know this message is long in the tooth, but I just came back across it while cleaning out old emails. ... I went by this fellow's booth at the Georgia AMO...
I posted a blurb about this last month, but still no takers; so here I am again. A local friend of mine has lost his storage and must sell a 75 Matador ...
NOTE: Several folks have replied asking where the car is. I did forget to mention it, but my phone number should have been a giveaway... Anyway, it is in...
Which city and state is it located in? VA area? Ralph americanmotorscorporationamc@yahoogroups.com wrote: There is 1 message in this issue. Topics in this...
I want to add cruise control on my 72 Gremlin when I rebuild it. I've got several sources for them. Can someone clarify all the necessary parts to pull. I ...
Hi All, I should have sent this message out a lot sooner, but there's still time if you don't wait too long. The Skagit County Historical Museum, located in La...
Allright, a bunch of folks wrote or called about this car, but it's still here. I really need to move it. It is in good condition and has a lot of life left...
AMC Fen, I like to drive "driver" cars; and as such I do not need collision or comprehensive insurance coverage. All I want is state minimum liability-only...
Some of my friends have managed to meet a few nice ones off this thing (here is the place they told me: http://www.friedchickedhere.info/jeeac , but what do...
barbi.elizabeth4657@...
Nov 1, 2005 3:30 am
1310
Trying to clean out the parts stash... ********************************************** If you need an extra hood for your Concord, here's your chance: ...
Does anyone have a 65 Classic 2 door thay can cut a driver's side quarter off of? I need it complete -- from door edge all the way back. -- Marc Montoni...
Another part of the AMC story passes on... <http://www.zwire.com/site/news.cfm?BRD=1399&dept_id=541142&newsid=15654990&PAG=461&rfi=9> -- Marc Montoni...
Too bad about Mr. Lemke. Keep on sending these things, I might even reply to one. I like the one a couple of days ago about the NASCAR matador. I live...
What year would AMC have gone to a locking torque converter in cars? I would like to switch out an old torque command for a newer one with a locking torque...
Bill, I did this to my Gremlin too. There are even little dents in the fender well that will show you where to drill for a factory install. I raided a Matador...
The lock-up torque converter would require a computer (ECU, MCU, or ECM) control to send the signal to the converter, something the 76 models didn't have......
AMC was using Chrysler's Torqueflite from 1972. Chrysler introduced a lock-up torque converter in 1978 and cars did not have computers in those days. The RWD...
Thanks Bill, That is the info I wanted. Todd ... introduced a ... those ... the lock ... Brougham ... torque ... proved a ... speed went ... mechanic ... ...
Bill answered your question. I left the AMC/Jeep dealer in 1979 when I was swooned over to the phone company to be a mechanic... so a lot of the 80's stuff I...
