I have too many tractors so wish to sell the following: Ferguson TO-20 Serial No. 17252 (1950) WITH Ferguson Loader Type L-UO-20 Serial Number 10670. I have...
Where are you located? frank_feathers <no_reply@yahoogroups.com> wrote:I have too many tractors so wish to sell the following: Ferguson TO-20 Serial No. 17252...
drippin out the bottom of my bellhousing,where the little hole is,,,guess its time to split the thing and repair stuff,Has any one done this? is it a major...
OK guys and gals I can now finally offer the North American version of this video, as I did with part 1. If you bought a copy of part 1, I will probably be...
OK guys and gals I can now finally offer the North American version of this video, as I did with part 1. If you bought a copy of part 1, I will probably be...
Hi! I'm about to cast a concrete rear weight for my -49 TEA20. I'm trying to make a replica of the original(?) weight I have seen in the pictures. Does anyone...
Hello All, Any suggestions for removing the lift arms from a 35X. The original holes for the lifting forks are elongated and I'm re-furbishing the lot before I...
If you try to remove the linkage from the switch it will drop into clutch housing. remove the setscrews from the switch and lift it up as far as you can, tie...
If you try to remove the linkage from the switch it will drop into clutch housing. remove the setscrews from the switch and lift it up as far as you can, tie...
Looking for a crankshaft for a to30 z129 continental crak# z129c500 OR is there some outher engine that will exchange with the z129 in a Harry Fergy to30 ser...
... z129c500 ... a ... I just checked Mikes Tractors and they have a crankshaft for the TO 30 however it is very costly. They also have a junk yard that I have...
I have ordered and just received 20 copies of this in NTSC (North American) format. It is a ~70 minute follow on to part 1, featuring another 25 Ferguson...
This may be a dumb question, but...You mention the "North American Version" of the video. What is different in the North American Version? "Jim Wallace...
I know I am a little late to the party, but I got all of my parts from this side of the ocean by going through Worthington Ag Parts near Winnipeg,Manitoba...
HI, Apologies. I have lost the e-mail with the address where to forward the money for Part 2. Mr Wallace, give me a clip on the head for not paying attention...
Dan, The North American television format is different than in England, such that you can't use a UK tape in a North American VCR. The content of the video is ...
Hi folks, we just got an FE35. It seem to be a solid low hour tractor, BUT the former owner forgot to mention that it wasn't equiped with oil pressure. I...
Have been in tractor business for over 45 years and have new and used tractor parts (Long, Mf and Ford) in stock for sale. Many hard to find parts. Email for...
We want to buy our first tractor & the above seems about the right size for us. Can anyone tell us if they have any form of PTO & what are they like to run ? ...
should have 540 rpm PTO speed no live hyd unless on a MF 35 great old tractors but I would suggest a newer one for farm work what do you intend to do with it? ...
Does anyone have a photograph of a Ferguson 3 ton trailer. I'm trying to locate one but won't recognise one if I see it! I have an ad in a free ads paper and I...
look in out club photo section at the left of the screen there should be a nice picture of a restored 3 ton ok regards rod ... Does anyone have a photograph of...
Hello.. I live in Nova Scotia and have a 1957?? MF gas 4 speed tractor. At the rear, I have a PTO adaptor shaft (with its own housing that bolts to the...
did you twist the PTO shaft off or did it have an adapter on it? try taylors tractor salvage in Truro for used parts. the adapters should be available at any...
Hi Rod, it was the adaptor shaft that broke. My adaptor shaft is only 5 1/2 inches long and has a bearing and cast housing that bolts onto the main housing...
there are a couple of options you could go to the newer shaft completely and eliminate the adapter altogether or if you are running things like a bushhog you...
I can't remember if I told you but I have the 460 page shop manual for the TE series copied and also the operators manual for it I sell these so if you need ...
