YOU need to take a test light and check bat.side of solenoid.If you have juice there then check starter side of solenoid with starter engaged.If no juice ...
Be sure the solenoid is properly adjusted, ie so the shift lever is actually engaging the solenoid. Also, if memory serves me right, you can clean the...
Hello everyone, I signed on earlier today when I found this group. For my part, I grew up around Massey Ferguson. For the most part, 135 and 165's were the ...
i am jack iam a new member and i have a 1982 furgoson and i want to get some new parts do you have any iders seeyaa. ... Find local movie times and trailers on...
... Y'all wouldn't have a picture of your 82 Furgo would yu, that you could post... Regards David ... get some new parts do you have any iders seeyaa....
Hi everyone, Good to see there is some life in this group. A lot of the others I am on are comatose or dead. If Bostick could take a look sometime and run this...
Hi All, Can anyone help me out with a slight problem. I wish to mate a baler to a T20 but knowing that the T20 does not have livedrive and is not fitted with...
I'm looking to rebuild the motor on my 1950 TO-20. Most of the kits I've found include the overbore 3 5/16 sleeves and pistons. Does the engine block need to...
they are just thinner sleeves, just make sure you clean up the walls real good and they will fit straight in Les <grayfort@...> wrote: I'm looking to...
Cooling System for TEA20 I have just replaced the radiator in my tractor, should I only use water in the radiator or is it ok to use a good quality coolant in...
Danny the part that you are describing sounds like the therostat. I have a To-30, but my thermostat is located inside the top hose to the radiator. My ...
Dear All, Does anyone know of the performance of an International B46 (or similar) Baler with the T20 TVO ?? I have seen a picture of them working together so...
Greetings Danny The temperature gauge you have is a mechanical one, and was probably not original on the tractor. If you want to test it, take the bulb out of...
Thanks to the members that posted the info I will check out the bulb to see if it does work now I know how to do it. Thanks once again to you both. Regards...
... they ... Hi Martin, the B46 was more suited to the fergie 35 range of tractors, in the main due to the dual clutch, as opposed to the single clutch on the...
Hi, could anyone tell me if there is a rotary hoe that would work on a TEA20 without reduction gears. I've been told that the tractor travels to fast at 4-klm...
hi all, i just purchased a massey MF-10 and need some parts. looking for a right rear axle housing or a transaxle. can anyone tell me why first gear is locked...
Need help in identifying my ferguson tractor. The plate by the steering wheel says it's a TEA 20 Serial #295985. The plate on the side of engine says Job...
Hello to you all, I am a student studying product design at university in London. As part of my course I have to write a dissertation about a design related...
Hi here is my opinion the Ferguson tractors had a good combination of simple design, fuel efficiency, ease of use, durablity and of course price. The tractors...
Hi here is my opinion the Ferguson tractors had a good combination of simple design, fuel efficiency, ease of use, durablity and of course price. The tractors...
Well, for what it is worth, I am one of the old timers. I presently own a 1944 Ford Ferguson. I am now 66 years old and when I was a child, my Dad bought a...
"frazerte20", can you promise us that you'll post your completed work here? ... My interest in the Ferguson comes not only from growing up with farm tractors...
I agree entirely with what Mike says. I wrote off-list to the enquirer with my own views as I've only recently sold my own TED20. I'm still very close to...
jonmac
jonmac@...
Aug 19, 2004 9:25 am
6712
Can anyone help?? I bought a Ferguson posthole digger the other day. I checked the oil and it was low so added some gearbox oil (how much oil should these two...
Hi, I was able to free the cog from the shaft that it was on. I soaked the shaft and cog in diesel over night and was able to knock the cog free of the keyway;...
