Does anyone know what the correct tension should be on the rear top link on the three point hitch. The to link hitch on my TO 30 has about 1/2" of play to it...
Hi Robb, The part you refer to is part of the draft control mechanism and it should have very little play in it, the correct setting is that with an implement...
Hi I have a TO 30 that has a front snow plow. I'm told by the local Ferguson dealer it must be an after market plow. It mounts to bolt hole in the front axle...
hi all i just purchased a MF 100 front loader with a front pump for my TO 35 but it was missing the drive shaft from pump to the tractor could any one tell...
Hey Bruce, I sure would like to see some pics of that rig you have there. I have the goodies to make up something similar but am not quite sure how to set it...
hi all evevidentlyheir must be two Bruce's in the club I brbruceokorisis not the proud owner of that fafantastic snow plow rig but it must be a brbrilook up...
Hi there is a company www.n-complete.com that used to have the pump and shaft parts give them a try anyway they have a good free catalog it is for Fords but...
I have a 1955 TO-35 and I am looking for a lower grille assembly (p/n 180 615 M91) and the instrument panel seal (p/n 180 674 M1) Does anyone know if these are...
you might try a search for ferguson on ebay I have found a few parts that way. William Bates 3234 State Route 9 Sedro-Woolley, WA 98284 ... From: bill02019 To:...
I have found a really good web site for selling and trading. I want to share it with everyone. The site is http://www.MYDREW.com ; They have a excellent social...
I have decided to tear down the 80mm engine on a 1950 Ferguson TEA 20 to determine the cause of the blue smoke and oil in coolant, and to give me something to...
Well, I don't know a whole lot. I'm having my 48' TE20 rebuilt as we speak. Hopefully i'll get it back this week. I can answer one of your questions though. I...
The Liners stand-out above the face of the cylinder block should be between .002" and .008". You should NOT use two liners gaskets under the liners, strictly...
You are correct, the stand-out of the liners above the block face should be between .002" and .008" If the liners are less than this you will need to remove...
John, Thanks for the great information. I did visit my local Massey- Ferguson dealer and they were able to get me the top end gasket set, the sleeve gaskets,...
Hi Ken, the problem with this is it is an 80mm bore and parts for those are getting hard to come by (pistons/cylinders/rings) you can still get them but they...
I have found trip bucket that was on a 1951 Ford 8N and got a good deal on it. I was wondering has anyone ever tried to convert it so it has a ram to work the...
Hello All I'm about to replace the draw arm attachment pins to the differential housing. I know I have to get inside the housing to open the nuts but what is...
I took the axle housing right off mine I was told you can take one side off think it was left one and reach across to get at other one I think it would be...
Thank You! It didn't really come to mind removing the axle housing but it does sound quite reasonable. The new pins I have are with nylock nuts on the inside,...
The correct way is to remove the LEFT side trumpet housing, you can get at them both then....it isn't a big job you could do it in a few hours easily. ... does...
I'm enjoying the group, although it's been years since I posted, I have run across something which does seem trivial, however, it is a very annoying and is a...
Are you sure that it is the gas cap that is leaking...we used to get the threaded ring that is part of the tank leaking and it required soldering properly to...
I also have had this leaking around the cap. At first I thought it was the gasket on the underside of the cap. I replace it; still leaked. It turned out to be...
I am in the process of rebuilding the engine on a TEA-20 80mm Ferguson. So-far-so-good, thanks to the help of this group. As I was rebuilding the head, I...
In a message dated 10/15/2005 7:41:41 A.M. Eastern Standard Time, no_reply@yahoogroups.com writes: I can help with frt.rims,but that is all. Bostick I have a...
