The extra seal you mention was fitted to later tractors after serial number 325001, your tractor will only have a single seal but what you can do is fit "Sure...
The guy who told you that I would stay well away from him. He is getting mixed up with the Ford 8N which has a cam and it isn't the cam that wears it is the...
Thanks very much for your help and advice John. I will track down the Sure Seals. I have a manual which explains brake set up etc. You are a very good judge of...
They say lightning never strikes in the same place twice, I have just finished an email to a neighbour of yours about his tractor a Mr Venus, perhaps you know...
Do not know Mr Venus. If you have time could you offer a sugestion or two on my hydralics on 3 point hitch. It has a tendency on sticking at the top when I...
Keep in mind that sure seals are a temp.fix.For a perm.fix,You have to bust collars and press bearings to get to seals.Bostick In a message dated 11/1/2006...
The position control device is called the Zane Thang. I don't have one yet, but I was going to get one. do a search for Zane thang and you will find it. ... ...
there is some adjustment of the quadrant but no position control I actually got a a Zane thang and it worked quite well for holding the front blade where I ...
Greetings Group, I seek a plug-in heater of some sort for my TO-30. I searched mssg archives and found 20+ mssgs talking about them - but no reference to a...
I put one in the radiator hose of one of my tractors got it off ebay for 5.00 it worked very well you had to cut the hose and fit it in they come in different ...
Good morning Rod - Thanks for quick response - all 'Gussie did this morning was groan a couple of times, got charger on now, will try again when warmer. ... OK...
clean all your connections up the ground cable also with 6 v you need very heavy cables and they have to be clean to get the starter spinning. I have used the...
Lunch break -- ... Thanks - will check and clean as needed --- crud, just checked, and there IS crud inside two connections - dammit........ I cleaned and ...
I always use either copper bearing anti-seize or an electrical product like noalox: http://www.idealindustries.com/wi/Accessories.nsf I also use the stuff at...
we bought ours for $1500 canadian - which is a way sweet deal in our opinion cause in good shape they usually go for $2000 to $2800 in the iSell out here...
Move the Ground lead to one of the bolts close to the starter, that will cut out any insulation that is taking place between the various components of the Dash...
... Sparex do a range of Block Heaters, some in bottom hose some magnetic, some in a core plug hole. email sparex(at)sparexusa.com for your nearest supplier,...
hey gang i just replaced the clutch in my ferguson f40 z134 continental... i went to adjust the clutch pedal and the problem i encountered was the throw out...
I have had a Zane thing for 5 or 6 years and it works about as well as you can get from the type of unit you are dealing with. As for being ultra precise I...
I have had a Zane thing for 5 or 6 years and it works about as well as you can get from the type of unit you are dealing with. As for being ultra precise I...
Very often in a new clutch assy there are three bolts that hold it all together before you fit it to the flywheel. Have you removed these bolts as that is what...
HI All, In review of the growing pile in my yard, anyone interested in a snow plow for a TO-20/30? The rear lift raises the 6' blade, manual swivel. Never...
Hello Everyone, I hope someone here can help me with this. I have A Ferguson, TE20 I believe, the lift arm falls, it won't stay up in a mid position, and if...
The Hydraulics on a TE20 or TO20/30 do not have Position Control which is what I think you are looking for, this can be fitted it is called a "Zane Thang"...
I went to start my TE-20 and move it to where it would sit for the winter. I shifted the gear lever to engage the starter and ... nothing happened. This is...
... Sometimes the obvious is not. 1)Is the battery dead? Turn on lights, if you have them, and check the brightness. 2)With the voltmeter connected to the...
Had similar issues when I bought mine solved a lot of the proformance issues simply by; A) make sure you have the propoer level of fluid. B) far more important...
