I used my P3 powered Fergie for the Lord Mayor of Westminster's New Year's Day Parade. I wasn't driving, so this is a second hand report. Apparently the...
... parts. ... bushings, ... lot ... and ... it ... I just sold a 9N that I did an alternator conversion on. FGabricating the lower mount was a toal PITA....
I would think its an airlock there may be a joint drawing air or perhaps some dirt got disloged and blocking fuel tank outlet check it out mine blocked once...
Probally an air lock after being appart or the tank outlet blocked -- - In fergusontractorclub@yahoogroups.com, "councillorjoiner" ... New ... report. ... ...
I'm looking to replace my cap & points. But the cap seems different on my TEA 20 then ours I've seen. Mine has regular push on spark plug wires. It doesn't...
Happy New Year all, Can someone explain how a starter motor will turn in the correct direction if the polarity is reversed? My mind is working overtime trying...
My TEF was a little bit harder to start recently, so I checked the seasons and it turns out we are in the middle of winter here!!! It warmed up nicely after...
Yes. The two windings in a starter are the armature and the field. They are wired in series in a starter. Whatever polarity you have for the DC power coming in...
Check that the breather hole in the fuel cap isn't blocked. If it is and you have a good gasket on the cap then the fuel being pulled through for x number of...
What's the best way to remove the paint from my tractor. I'm concerned if I sand blast it that the sand will get into places that I don't want it to be....
... I'm not sure it's the *best* way, but after removing the fenders and bonnet from my '52 TO30, all painted red (I swear, some of the areas were coated in...
I know it is the usual thing to retain the original color scheme on machinery but I think I'm going to break rank and use something other than the dullness of...
For stripping to bare metal there is nothing better than a 4or 4.5" grinder and a round stainless brush, a cup brush and possibly one of those flap wheel disks...
I had my TE20 (number 4869, 1947) gritblasted (= sandblasted, but Health-and-Safety-compliant) professionally by my son-in-law: we stripped down everything...
In reply to Jesse's questions - I've spoken to the pro - my son-in-law who's a professional blaster; he says: "We used my pro setup, which is a big fixed...
The lift stays up quite a while after the engine is shut off, probably 5 minutes or longer, much longer than my TO35 (which stays wherever I put it while in...
Position control for the Ferguson system Main >> Business Park >> Mail-Order Businesses Position control for the Ferguson system Position control for the...
Thanks for the advice guys. The cap was ok, and I finally got around to having a look at my injector pump. I squirted fresh engine oil as you recommended John....
When you put fresh oil in the Injection Pump did you allow it to run out of the tap at the bottom until it was just oil and let it find it's own level. Yes it...
So from what you saying then, does the dynamo earth through its mounting bolts, and find a path back to earth? Because my dynamo is not making a 'clean'...
I opened the tap and let all the additional oil run out. I then got a few drops of fuel out but nothing major, and then I closed the tap again. That leak seems...
Hi Everybody, Looking for 2 bottom 3 point linkage rails for TEA20. Still in good order plus connecting units to diff. Mine are pretty worn out. Just about had...
Hello all... Perhaps someone can help me out. I have a ferguson tractor that has a serial no. plate right above the steering wheel. It says TEA 269206. Can...
You can find some of that here http://www.centralia.net/tractor/sernum.htm According to the list she was built in 1952. From what I know the main difference...
Jeff I have the TEA 20 shop manual both as a paper version and on a CD also have the operators manual and the parts books for sale drop me an email at ...
