Steve, Don't know about your ISPF panel definition but, I have a REXX routine that searches multiple PDSs for a specified member name. It calls an Assembler...
... <steve.wilhite@p...> wrote: ... save ... Try using the following ISPF Services: TSO ALLOCATE FILE(ddname) DSN( max 4 concatenated PDS ) SHR LMINIT...
I am beginner in MF. I am confuzzed in lots of docs. given: a Z900/running OS/390 to connect to a EMC Symmetrix 8530 via Escon director. Z900----ESCON...
I cannot answer for sure as we don't have EMC. I assume that you configure the storage space in virtual 3390 dasd. Therefore you should configure as many...
many thanks. From your IOCD statement, is that right? ... and the storage system appear to Z900 to be two 3390-6 CU.e.g, SSID are x1 and x2. so, there are 4...
The IOCP Input deck I used was actually copied from the IOCP User Guide. What I would do is to define 256 devices for each CUADD for the 3390 architecture. So,...
many many thanks. swiss_tikier I see. your opnion is: 1. make sure devive address and number specification, eg.768 devices ,range device number 1300-15FF so,...
Hi: ISPF doesn't have a primer manual but instead has the ISPF User's Guide (in 2 volumes). Please check for "z/OS V1R2.0-V1R4.0 ISPF User's Guide Vol I ...
Hi all, what should be the values for 1. Control Unit number, 2. Switch Types, 3. Port Number, 4. Supported Channel Attachment to define a 1403 printer? TIA ...
Hi: An IBM 1403 printer typically attaches to an IBM 2821 Control Unit, connect to a Byte or a Block Multiplexor Channel (paralel, dedicated) and you don't...
Hi Cesar, Thanks for the information. Regards, Kailas ... dedicated) ... device ... <http://rd.yahoo.com/SIG=12cminjbv/M=267637.4116732.5333197.1261774/D= ...
Hi Friends, This is Ravi Kumar.i need faqs of cobol,jcl,cics,db2,vsam,ims.plzzz send me. bye Yahoo! India Mobile: Ringtones, Wallpapers, Picture Messages and...
HI FRIENDS, THIS IS RAVI KUMAR FROM HYDERABAD,INDIA.PREVIOUSLY IAM WORKING AS A PROGRAMMER ON JAVA TECHNOLOGIES.BUT NOW IAM SHIFTING TO ANOTHER TECHNOLOGIES IE...
Ravi, What type of help are you looking for? Are you using MVS, OS/390, z/OS? What type of mainframe do you have to work on? Any LPARs? Peter ... ===== Peter...
Hello all. The JES2 doc clearly states that changing this can be achieved by using the $t or a cold start. What I can't seem to determine (and can't recall)...
No., you should be fine. When you IPL next, check to see if JES2 produces a message to say - Found this definition in the PARM but last time it was this, so I...
Hi all i want know whether there is possible to copy one authorized command such as xmit to anthoer name into myself PDS. and then whether I can use the new...
Do you have specific manuals/books in mind? Are you asking about the IBM Manuals or REDBOOKS? Or something else? For IBM Manuals/ Redbooks; depending on...
The most likely explanation is that the member in parmlib that authorizes the use of certain functions in TSO does not contain your new name. Under TSO things...
... Yes, this is a 'must do' for commands that are authorized. The member used at IPL is always IKJTSO00. You may create a member named IKJTSOxx and activate...
thank both of you Wolfgang and Lizette. I understand it now. In fact, I just want know MVS or OS/390 how to control this type action. I know little about...
Hello to all Sorry for my bad english I am beginner for OS/390. I have downloaded many software but i can't install them. I recieve an error. i have a...
