hey guys. new guy here.I have a problem with my 95 gt.it has no balls when yo jump on it after the first 2 mins of it running.I have replaced the o2 sensors...
bob, I had the same problem with my 89 GT. I replaced the EGR valve and this did wonders. If this doesnt do the trick (most likely will) then you should check...
... HEY, BOB, BEFORE YOU DO ANYTHING RUSH, THE BEST TO DO IS CONNECT TO YOUR CAR THE DIAGNOSTIC SCANNER, IS THE ONLY WAY TO LOOK UP FOR CODES TO ADRESS YOU TO...
sounds like the IAC valve is going out, you have any problems sitting at idle also? Thank you very much. Sincerly, Samuel P. ... Do you Yahoo!? Meet the...
I have an 1988 mustang with no horn. It didn't work before at at. I took off the stearing wheel cover and connected it. Now whenever I press it I just hear...
Sounds to me like you're only hearing the relay. I'm guessing the horns were removed. ... From: vincentpghpa [mailto:vincentpghpa@...] Sent: Wednesday,...
hey all i just wanted to let yall know about the new website me n the stang crew have made up. its still under construction. but id like if yall came and...
yes i already replaced the iac valve and the tps.But now the car is going to be down for the winter so i brob will worry about it in spring.Since during the...
pics posted under bobs stang car still needs the paint done and the foglight installed.But can you figure out why the import guys hat me? LOL Let me know what...
i just switched out a 92 4cyl for a 85 cfi 302- i only have a two barrel right now but the question is can i disc. all computer stuff and still wire up the...
Anyone know of free catalogs for 88 mustang parts? How hard is it to fix/install electronic locks? Anyone know the best book for manual transmissions? I am...
CD and tape deck? We are in the 2000's... Get rid of tapes. You can d/l all those tapes onto CD via bit torrent, emule, edonkey etc. Tapes = poo quality. But...
Anyone know were the turn signal flasher can or trigger can is located? Also in the fuse box there is a round opening for a hazzard trigger can. This is...
I need to sell some 4.6L parts anyone interseted e-mail me a maddogfriar21@.... New 4.6l block, 2 right side heads bare, 2 complete heads an intake from...
My father in law has a 351w that he wants to build into a 408 stroker. I was wondering if anyone could tell me what cam and head setup he should use? Thanks...
I've got a 93 Mustang 5.0 H.O. coupe that I am looking to do some modifications to. The car is totally stock and has no aftermarket parts on it. I'm looking...
Hi David, ... I have had good luck with MAC over the years and like them --not everybody agrees though. ... ON a relatively stock motor you will loose a bit of...
Steven W. Critchlow
swc@...
Feb 3, 2005 8:25 pm
608
Hi, ... That motor will need GOOD breathing ported heads to realize it's full potential. If it's not a sanctioned race motor you might want to look into Yates...
Steven W. Critchlow
swc@...
Feb 3, 2005 11:00 pm
609
GoodAfter Noon, I just wanted to take the time to send you our new web address we are a newFord Racing, Roush, and Saleen performance parts dealer and wanted...
Thanks for the reply Steven! I'm looking for a rough idle as well as the loud exhaust. It appears that I've got the exhaust figured out so now I'd like a...
Hi David, ... No problem :) ... Keep in mind that sometimes the rough idle means less power--cam/head selection is very important. ... Ideally you would want...
Steven W. Critchlow
swc@...
Feb 4, 2005 7:18 pm
612
... site for 5.0 mods that caught my eye a few months back.. ENJOY! www.allfordmustangs.com/forums/showthread.php?t=1337 ... __________________________________...
I have a 1990 Mustang GT Convertible that i bought in 2002 that had 25,000 original miles.. The car has gold 5.0 emblems and the ford emblems on the front in...
Hi, ... I believe all but the wihit leather is aftermaeket--I think that someone pimped up the car themselves. I'd be interested in hearing if it was factory...
Steven W. Critchlow
swc@...
Feb 7, 2005 10:15 pm
620
if im not mistaken the flasher is on the back side of the fuse box.pull the fuse box out and you should see it. pwdcougar <CU351@...> wrote: Anyone know...
the flasher cam or trigger is located in the turn signal switch twinturbostang87@... wrote:if im not mistaken the flasher is on the back side of the fuse...
I'm looking at doing some engine mods and I'm trying not to spend a whole lot of money but get the best performance. I'm currently looking at GT-40 heads,...
